HOn30 Trackwork Mini HowTo

Intro

roadbed-balast-icrr.png
Gravel or Cinder Ballast, Illinois Central R. R.
roadbed-balast-prr.png
Stone ballast, Pennsylvenia R. R.
turnout-split-switch.png
Turnout with split switch
frog.png
Frog

Prototype

Standard gauge trackwork somewhere in New England. Wood ties and nails are still used in 1996. You can see a rail anchor in the third picture, a detail very seldom modelled.

A friend gave me some photos from the 3 foot narrow gauge railroad White Pass and Yukon Route. Maybe original tracks from 1898.

You can see a 76 cm narrow gauge line crossing two standard gauge tracks in Weiz, Austria. The Switch is in Bikfeld. The trackwork looks very american for my opinion.

Some industrial 60 cm and 75 cm gauge trackwork in Switzerland.

Waldenburger Bahn, the only 75 cm gauge commuter train in Switzerland (probably in the world).

Narrow gauge double slip switch. RhB Italy/Switzerland.

HO / HOn30 Tracks

Rails

One of the narrow gauge advantages was the use of lighter rails and therefore the lower investment. Lighter rail looks better and is more prototypical. The rails were 33' long til about 1925.

Rail Code Height [mm] Weight [Pounds per Yard] Weight [kg/m] DIN 5901
40 1.0 40 18.3 S 18
55 1.4 80 33.5 S 33
70 1.8 100 54.5 S 54
80 2.0 136 64.9 S 64
83 2.1 140 64.9 S 64
100 2.5 156 - -

Quotation from Railway Track and Maintenance (1926): For ordinary main-line service, 80 lb. is about the minimum weight and 100 lb. rails are in general use.

80 lb. rail from A.S.C.E: height 5" (HO 1.46 mm), base 5" (HO 1.46 mm), this corresponds in HO to code 55, 100 lb. corresponds in HO to code 70. Early narrow gauge lines used 40 lb. and lighter rail.

rail.gif

Quotation from Maine Two Footers On2 FAQ:

  • SR&RL rail weights, information from 1916, but weights probably did not change too much after then (before that is not a simple answer)
    • Farmington - Strong - Phillips weights varied from 50 - 52 - 56 & 58 1/4 lbs (most of it 10.48 mi. was 52lb).
    • Phillips to Madrid Jct. 50 lb rail laid in 1919
    • Almost everything else was 35 lb rail
    • At time of abandonment, there was a reported 2 mi. of 60 lb rail
  • B&B Rail was 25 lb, 30ft lengths.
  • B&SR Rail Weights
    • Bridgton Jct to Bridgton, prior to 1909: 30 & 35 lbs
    • Bridgton Jct to Bridgton, after 1909 : 50 lbs.
    • Bridgton yard relaid with 50 lbs rail in 1910
A good compromise is to use code 55 rail for HOn30 and code 70 for standard gauge. Ties

Ties

  • Standard gauge until 1918: 8' long (HO 28 mm)
  • Standard gauge after 1918: 8.5' long (HO 29.8 mm), sometimes 9' (HO 31.5 mm)
  • width: 7 .. 9" (HO 2 .. 2.6 mm), thickness: 7 .. 8" (HO 2 .. 2.3 mm)

PRR practice (standard gauge)

center-to-center main lines 22" 6.4 mm
center-to-center sidings 24.8" 7.2 mm
center-to-center yards 28.3" 8.3 mm

Sächsische Bahnen (Saxonian Railways, Germany), 750 mm gauge

Width 200 mm 2.3 mm
Length 1.7 m 20 mm
center-to-center main lines 750 mm 8.6 mm
center-to-center sidings 830 mm 9.5 mm

SR&RL

Width 5" 1.5 mm
Length 5' 17.5 mm

overhang (5'-2)/2 = 1 1/2' -> tie length for HOn30: 5.5' (19.3 mm)

Campbell Ties:

HO 1.3 x 2.4 x 28 mm
H0n3 1.3 x 2.4 x 21 mm

They are relative thin (1.3 mm), to prevent splitting (nails), less gravel is needed to cover the ground.

Micro Engineering full profile Ties (37-103):

HOn3 1.7 x 2.3 x 23.5 mm

PCB ties are about 1.6 mm / 1/16" thick)

Fast Track HO narrow gauge PCB crossties:

HOn3 1.6 x 2.0 x 24.4 mm
HOn30 1.6 x 2.0 x 20.1 mm

PCB crossties are 13-1/2 scale feet long by 7 scale inches wide (.080"), and are available in 1/16" and 1/32" thickness.

I cut my ties from a 1.6 x 100 x 160 mm printed circuit board PCB (in Switzerland it is available from Distrelec, Partnumber 450335, for 2.50 CHF that's about $2). I prefer FR-2 PCBs, because the FR-4 (glass/epoxy) makes your sawing blades dull. I saw about 2.3 mm stripes from the PCB with a fretsaw and cut the ties to length (20 mm) with a wire cutting pliers. I choose 8 mm (27" prototype) center-to-center distance for my pike. The Fast Track choose 24" for branch and 21" for main line.

The Micro Engineering ties have about the same thickness and width and can be used together with my PCB ties. It's enough to insert a PCB tie for about every 4th tie.

FR-2 is composite material made of paper impregnated with a plasticized phenol formaldehyde resin (Synthetic Resin Bonded Paper (SRBP), Bakelite, Lamitex, Paxoline, Pertinax)

FR-4 is a composite of a resin epoxy reinforced with a woven fiberglass mat (epoxy resin bonded glass fabric (ERBGF), Veroboard) printed circuit board (PCB)

Spikes

Cut spikes are about 6" long, the spike head is about 1 9/16" x 1 5/16" in HO is this 1.75 x 0.46 x 0.38 mm. The small spikes from Micro Engineering are 8.0 x 1.7 x 1.0 mm, they are far too large. You can build your own spike from 0.4 mm wire, you have to drill holes into the ties too. That's why I omit the spikes.

Tie Plates

Tie plates were not always used for narrow gauge tracks. But normally they were found at least on turnouts and in curves. They are 5" to 10" wide and about 1/2" (HO 0.15 mm) thick. Tie plates for HO are too small and too difficult to build for me. I omit tie plates on my tracks.

Tips

Tools needed

  • Moto tool with a cutting disc or alternative needle files (Swiss files) and lot of patience
  • Jewelers Saw
  • Regulated Soldering iron e.g. from Weller
  • Fretsaw
  • Wire cutting pliers
  • Needle nose pliers
  • NMRA Standards gage for HO and N
  • track gauges for HO and N e.g. from Rail Craft

Soldering tips

  • use a regulated soldering iron e.g. from Weller
  • use small diameter electronic grade solder
  • flux is already included in the electronic grade solder (additional flux is not needed)
  • solder only from the outside of the rail
  • clean all surfaces: the rail, the PCB, and the tip of the soldering iron (dirt is the enemy of a good quality soldered joint)
  • heat both the PCB and the rail before adding the solder
  • remove excess solder with desoldering braid (Soder-Wick)

How To Scratch Build a Narrow Gauge Standard Gauge Crossing

As far as I know there is no commercial narrow gauge standard gauge crossing available. It takes me about 4 h to build a "diamond" from scratch. You need only only some code 70 rails and PCB cross ties.

Step by step instructions to build a crossing from scratch:

Print out a template

e.g. from Fast Tracks " target="_blank">http://www.handlaidtrack.com/]] the HO 30° Crossing Template. Reduce one leg to 9 mm (HOn30) gauge and glue the template on PCB (I use white glue).

Glue the crossties to the template

For the first crossing I built, I used for every second tie a PCB tie. Now I use for all ties PCB ties.

Solder the first rail from the mainline (usually the standard gauge leg) to the ties

Solder the second rail to the ties, use a HO track gauge to ensure the right distance between the rails.

Bend the two guard rails for the mainline and solder the rails next to the mainline rails

Check the flangeways with a NMRA HO gauge.

Bevel the end of a rail and solder the first crossing rail to the ties and to mainline rail

The rail heads should touch each other, to achive this I remove about 1 mm from the base of the crossing rail. Solder second crossing rail to the ties and to mainline rail, use N track gauge to ensure the right distance between the rails.

Cut and bevel a rail to the length between the two mainline guardrails

Use a straight edge to guide the rail and solder the rail to the ties. Finish the crossing rails

Bend the outer guard rails for the narrow gauge line with a needle nose pliers

Bevel the ends and solder the rails to the PCB ties. Insert the inner guard rails for the narrow gauge line.

Cut the mainline rails and the guard rails for the HOn30 flangeways with a cutting disc moto tool.

Put the crossing in warm soapy water and remove the crossing from the PCB

Cut the isolating gaps with the fretsaw trough the rails and the ties.

How To Convert an Atlas N Code 55 Turnout to HOn30

Commercial available HOn30/H0e/009 turnouts from Peco, Tillig, Technomodell, and Roco have too heavy rails (Code 80/83) and too wide angles (15 °, less than #4). You can build the turnouts from scratch, but for me it is difficult and to time-consuming to build the heel of the switch (especially the hinge) and the frog. The N code 55 turnouts from Atlas are available with frog numbers #5 and #7 (for details see http://www.atlasrr.com/Trackmisc/ncode55.htm). Code 55 #5 turnouts are exactly what I am looked for. They cost about $10 each. The only thing you have to do is to replace the small plastic ties with larger PCB ties.

Print out a template

e.g. from Fast Tracks " target="_blank">http://www.handlaidtrack.com/]] the HOn30 #5 Turnout Template and glue the template on PCB (I use white glue). Lay the N gauge turnout on the template and mark with a pencil the frog and the toe of point on the template.

Remove the rails from the plastic ties

Remove the pins from the frog and the guard rails.

Glue the crossties to the template

Solder the straight stock rail to the ties

Use a straight edge as a guide.

Solder the frog to the ties

Use a NMRA N gauge to check the distance between the stock rail an the frog. The lead (distance between toe of point and frog point) is 75 mm.

Solder the second stock rail to the ties

Check the gauge between the stock rails and between the stock rail and the frog.

Solder the two rails to the frog heel (frog point rail) and to the frog toe (closure rails)

Use a N track gauges to ensure the right distance between the rails. Solder the two guard rails to the rails.

Solder the switch tabs to the heel of the point

Make sure that the rails are in line.

Cut gaps into the copper foil ties

Put the turnout in warm soapy water and remove the turnout from the PCB.

Fill the gaps with filler, sand and paint the turnout.

HOn30 #5 Turnout in Comparison With Shinohara HO #6 Code 100

switchstand.jpg
Switch Stand, DPDT slide switch

How To Build a HO Switch with CVT Turnout Ties

There is nothing wrong with the Turnout Kits from Central Valley Model Works, they look fantastic, but I want an powered frog (frog switching see https://dccwiki.com/Turnout) and a reliable throw rod (PCB tie-bar). Therefore I need only the CVT Turnout Ties and not the Turnout Kit.

cvt-switch-2.jpg
CVT Switch Kit #2571, #5 LH Code70
cvt-switch-1.jpg
PCB throw bar, switch point and hinges
cvt-switch-frog-1.jpg
Frog isolation gaps
cvt-switch-primer-1.jpg
Turnout painted with Tamiya Surface Primer spray
 

  1. Notch the stock rails (I use the StockAid tool form Fast Tracks), notch starts about in the middle of the first head block tie
  2. Glue the straight stock rail to the ties
  3. Bend the curved stock rail till it fit to the tie plates and glue it to the ties
  4. File the frog point rails (I use the PointForm tool from Fast Tracks) and solder the halves together
  5. Glue the the frog point to the rails
  6. File the point rails (I use again the PointForm tool from Fast Tracks)
  7. File or saw a notch into the straight closure rail, bend the track (it should be parallel to the frog point rail), cut it to the length and bevel it, glue it to the ties
  8. Bend the curved closure rail til it fit to the tie plates
  9. File or saw a notch into the curved closure rail, bend the track (it should be parallel to the frog point rail), cut it to the length and bevel it, glue it to the ties
  10. Remove 6 plastic ties and the head tie
  11. Solder the PCB ties to the rails, do not solder the inside of the second switch stand tie
  12. Solder the throw PCB to the switch points, but not on the stock rail side
  13. Cut gaps to isolate the frog. I use a jewelers saw
  14. Cut the rail base and part of the head (but not the rail web) to build a hinge
  15. Solder the guard rails to the PCB ties or glue the plastic guards to the ties
  16. Glue the rail-braces to the ties (e.g. from Central Valley or Details West RB-920)

turnout-split-switch.png
Turnout with split switch
frog.png
Frog
split-switch.png
Split Swich
rail-brace.png
Rail Brace
rail-joint.png
Rail Joint, Chicago & Northwestern Ry., Fishplate,

Bibliography

  1. Paul Mallery, Trackwork Handbook, Carstens Publishing, ISBN 911868-86-0
    THE reference for trackwork. If you want to buy only one book about trackwork, you should buy this one. Subtitle Everything You Need to Learn to Know About Track
  2. E. E. Rusel Tratman, Railway Track and Maintenance, Original printed in 1926, Kalmbach Memorial Library NMRA, ISBN 0-9647050-6-0
    It's still the best way to learn from the real thing.
  3. Kent Johnson et al, Trackwork and Lineside Detail, Kalmbach Publishing, ISBN 0-89024-71-1
    The best of from Model Railroader to this topic.
  4. Maj. W. D. Connor, Military Railways, Government Printing Office, 1917, see Georg Schreyers scannings on http://www.girr.org/girr/military_railways/military_railways.html
  5. J. B. Calvert, Turnouts
  6. Wikipedia, Railroad Switch
  7. Fast Tracks, Source of Quality Tools, Supplies and Information For Hand Crafted Track.

-- PeterSchmid - 2011-05-09

Creative Commons License
This work by Peter Schmid is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Topic attachments
I Attachment History Action Size Date Who Comment
JPEGjpg atlas-closure-small.jpg r1 manage 5.9 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg atlas-closure.jpg r1 manage 50.3 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg birkfeld-switch-small.jpg r1 manage 12.6 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg birkfeld-switch.jpg r1 manage 123.8 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg crossing-crossties-small.jpg r1 manage 7.5 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-crossties.jpg r1 manage 62.0 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-firstrail-small.jpg r1 manage 8.7 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-firstrail.jpg r1 manage 74.1 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-gap-small.jpg r1 manage 12.1 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-gap.jpg r1 manage 108.5 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-guardrail-small.jpg r1 manage 8.4 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-guardrail.jpg r1 manage 113.3 K 2011-05-12 - 21:09 PeterSchmid  
JPEGjpg crossing-mainline-s.jpg r1 manage 9.1 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-mainline.jpg r1 manage 76.9 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-mainline2-small.jpg r1 manage 7.3 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-mainline2.jpg r1 manage 59.4 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-secondrail-small.jpg r1 manage 7.7 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-secondrail.jpg r1 manage 62.9 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-template-small.jpg r1 manage 6.8 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-template.jpg r1 manage 63.1 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-ties-s.jpg r1 manage 9.6 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-ties.jpg r1 manage 84.1 K 2011-05-12 - 21:13 PeterSchmid  
JPEGjpg crossing-wo-gap-small.jpg r1 manage 11.1 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg crossing-wo-gap.jpg r1 manage 93.5 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg cvt-switch-1.jpg r1 manage 358.9 K 2023-07-09 - 13:58 PeterSchmid  
JPEGjpg cvt-switch-2.jpg r1 manage 297.6 K 2023-07-09 - 13:58 PeterSchmid  
JPEGjpg cvt-switch-frog-1.jpg r1 manage 230.1 K 2023-07-09 - 13:58 PeterSchmid  
JPEGjpg cvt-switch-frog-2.jpg r1 manage 222.1 K 2023-07-09 - 13:58 PeterSchmid  
JPEGjpg cvt-switch-primer-1.jpg r1 manage 343.4 K 2023-07-09 - 17:50 PeterSchmid  
JPEGjpg cvt-switch-primer-frog-1.jpg r1 manage 328.0 K 2023-07-09 - 17:54 PeterSchmid  
JPEGjpg cvt-switch-primer-point-1.jpg r1 manage 388.7 K 2023-07-09 - 17:50 PeterSchmid  
JPEGjpg doubleslip-s.jpg r1 manage 19.1 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg doubleslip.jpg r1 manage 209.6 K 2011-05-11 - 20:34 PeterSchmid  
PNGpng frog.png r1 manage 656.9 K 2023-07-16 - 09:32 PeterSchmid  
JPEGjpg gonzen-track-small.jpg r1 manage 22.1 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg gonzen-track.jpg r1 manage 250.7 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg ho-hon30-side-small.jpg r1 manage 7.3 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg ho-hon30-side.jpg r1 manage 72.0 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg ho-hon30-small.jpg r1 manage 12.9 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg ho-hon30.jpg r1 manage 142.7 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg industrial-track-small.jpg r1 manage 8.6 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpg industrial-track.jpg r1 manage 82.9 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpeg maine-frog-small.jpeg r1 manage 10.5 K 2011-05-11 - 20:34 PeterSchmid  
JPEGjpeg maine-frog.jpeg r1 manage 104.2 K 2011-05-11 - 20:47 PeterSchmid  
JPEGjpeg maine-track-small.jpeg r1 manage 10.8 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpeg maine-track.jpeg r1 manage 103.0 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpeg rail-anchor-small.jpeg r1 manage 18.6 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpeg rail-anchor.jpeg r1 manage 172.4 K 2011-05-11 - 20:36 PeterSchmid  
PNGpng rail-brace.png r1 manage 693.8 K 2023-07-16 - 11:01 PeterSchmid  
PNGpng rail-joint.png r1 manage 1774.4 K 2023-07-16 - 11:19 PeterSchmid  
GIFgif rail.gif r1 manage 9.3 K 2011-05-11 - 21:00 PeterSchmid  
PNGpng roadbed-balast-icrr.png r1 manage 796.4 K 2023-07-16 - 09:58 PeterSchmid  
PNGpng roadbed-balast-prr.png r1 manage 1500.8 K 2023-07-16 - 09:58 PeterSchmid  
GIFgif spike-h.gif r1 manage 5.2 K 2011-05-12 - 05:41 PeterSchmid  
GIFgif spike.gif r1 manage 12.3 K 2011-05-12 - 05:41 PeterSchmid  
PNGpng split-switch.png r2 r1 manage 3192.5 K 2023-07-16 - 10:08 PeterSchmid  
JPEGjpg straight-edge-small.jpg r1 manage 6.0 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg straight-edge.jpg r1 manage 57.7 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpeg switch-stand-small.jpeg r1 manage 11.0 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpeg switch-stand.jpeg r1 manage 111.0 K 2011-05-11 - 20:36 PeterSchmid  
PNGpng switchstands.png r1 manage 2267.6 K 2023-07-16 - 09:32 PeterSchmid  
JPEGjpg trackwork-s.jpg r1 manage 71.8 K 2015-03-01 - 14:06 PeterSchmid  
JPEGjpg turnout-gaps-small.jpg r1 manage 9.4 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg turnout-gaps.jpg r1 manage 96.4 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg turnout-hon30-small.jpg r1 manage 5.5 K 2011-05-12 - 21:14 PeterSchmid  
JPEGjpg turnout-hon30.jpg r1 manage 46.0 K 2011-05-12 - 21:14 PeterSchmid  
PNGpng turnout-split-switch.png r1 manage 729.3 K 2023-07-16 - 09:32 PeterSchmid  
JPEGjpg wb-frog2-small.jpg r1 manage 10.8 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpg wb-frog2.jpg r1 manage 132.7 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpg wb-switch-small.jpg r1 manage 12.6 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpg wb-switch-stand-small.jpg r1 manage 10.0 K 2011-05-11 - 20:36 PeterSchmid  
JPEGjpg wb-switch-stand.jpg r1 manage 112.6 K 2011-05-11 - 20:49 PeterSchmid  
JPEGjpg wb-switch.jpg r1 manage 158.1 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpg wb-transition-small.jpg r1 manage 12.8 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpg wb-transition.jpg r1 manage 169.8 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg weiz-crossing-small.jpeg r1 manage 17.1 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg weiz-crossing.jpeg r1 manage 152.2 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg weiz-crossings-small.jpeg r1 manage 11.0 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg weiz-crossings.jpeg r1 manage 96.0 K 2011-05-11 - 20:48 PeterSchmid  
JPEGjpeg weiz-track-small.jpeg r1 manage 19.9 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg weiz-track.jpeg r1 manage 181.7 K 2011-05-11 - 20:38 PeterSchmid  
JPEGjpeg white-pass-frog-2-small.jpeg r1 manage 17.1 K 2011-05-11 - 20:39 PeterSchmid  
JPEGjpeg white-pass-frog-2.jpeg r1 manage 159.2 K 2011-05-11 - 20:39 PeterSchmid  
JPEGjpeg white-pass-small.jpeg r1 manage 10.3 K 2011-05-11 - 20:39 PeterSchmid  
JPEGjpeg white-pass.jpeg r1 manage 106.6 K 2011-05-11 - 20:39 PeterSchmid  
JPEGjpeg white-passw-frog-small.jpeg r1 manage 15.2 K 2011-05-11 - 20:39 PeterSchmid  
JPEGjpeg white-passw-frog.jpeg r1 manage 149.9 K 2011-05-11 - 20:39 PeterSchmid  
Edit | Attach | Watch | Print version | History: r14 < r13 < r12 < r11 < r10 | Backlinks | Raw View | Raw edit | More topic actions
Topic revision: r14 - 2023-07-16 - PeterSchmid
 
This site is powered by the TWiki collaboration platform Powered by PerlCopyright © 2008-2024 by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding TWiki? Send feedback