(r2) RaspiElfDisplay < Cosmac

Tags: view all tags
%DASHBOARD{ section="dashboard_start" }%
%DASHBOARD{ section="banner"
 image="%PUBURLPATH%/Cosmac/RaspiElf/raspi-elfmemcard-s.jpg"
 title="!RaspiElf Display"
 titlestyle="color:#F00000;"
}%
%DASHBOARD{ section="box_start" title="Intro" width="485" height="200"}%
Long time ago I built a LED display and a hex keypad for my [[Cosmicos][COSMICOS]]. I lend the COSMICOS and the extensions to a friend's brother and I saw the parts never again. Thanks to Lee Hart's [[http://www.sunrise-ev.com/membershipcard.htm][1802 Membership Card]] I have a 1802 SBC again. Now I need a display and a keypad for this gem.
%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="box_start" title="Contents" width="460" height="200"}%
%TOC%
%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="box_start"  width="992" height="400" }%
---+ Hardware
TIL311 hexadecimal displays were to expensive for me 35 years ago and now they are not easy to get (and still expensive). The 4×7 rounded font looks far better than the seven-segment display especially the lower case hex display letters. But there is an alternative: LTP-305 from LITEON. They have no integrated driver, but the matrix LED driver IC !IS31FL3730 can drive two of them. And better there is [[ttps://shop.pimoroni.com/products/microdot-phat][PCB HAT]] with 6 LTP-305 and 3 !IS31FL3730 on it from Pimoroni ready for the Raspberry Pi. Four digits for the address and two digits for data! 

| %IMAGE{"%PUBURLPATH%/Cosmac/RaspiElfDisplay/til311.jpg" type="thumb" caption="TIL311 Hexadecimal Display"}% \
| %IMAGE{"%PUBURLPATH%/Cosmac/RaspiElfDisplay/LED_module.jpg" type="thumb" caption="LTP-305 Dot Matrix Display"}% \
| %IMAGE{"%PUBURLPATH%/Cosmac/RaspiElfDisplay/Microdot_pHAT.jpg" type="thumb" caption="Microdot_pHAT on Raspberry Pi Zero"}% |

https://shop.pimoroni.com/products/microdot-phat


%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="box_start"  width="992" height="600" }%
---+ Software for the Raspberry Pi
The Raspi controls the display through its I2C interface.

I still want to use the [[http://www.sunrise-ev.com/membershipcard.htm][1802 Membership Card's]] Front Panel Card. That means I have to use the D-SUB connector. But there is no address bus on this connector, therefor the address is only valid as long as the DMA (load mode) is used. The data bus is not available too, you will see the data in the load mode and the output port during the run mode.   

%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="box_start"  width="992" height="380" }%
---+ How to get and build the RaspiElf Display Software

Get the source from the [[https://github.com/spyren/RaspiElf][GIT repository]] (if you have not installed GIT yet, then install it with
=sudo apt-get install git=), type only the bold text after the $ sign:
<pre>
pi@cosmac:~/elf $ <b>git clone https://github.com/spyren/RaspiElf</b>
Cloning into 'RaspiElf'...
remote: Counting objects: 68, done.
remote: Compressing objects: 100% (37/37), done.
remote: Total 68 (delta 32), reused 62 (delta 29), pack-reused 0
Unpacking objects: 100% (68/68), done.
Checking connectivity... done.
pi@cosmac:~/elf $
</pre>

Build (compile) from the sources:
<pre>
pi@cosmac:~/elf $ <b>cd RaspiElf</b>
pi@cosmac:~/elf/RaspiElf $ <b>cd display/</b>
pi@cosmac:~/elf/RaspiElf/display $ <b>make</b>
... TBC
</pre>

Install the binaries into =/usr/local/bin=
<pre>
pi@cosmac:~/elf/RaspiElf/display $ <b>sudo make install</b>
... TBC
</pre>
%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="box_start"  width="992" height="600" }%
---+ TIL311 Emulator
The TIL311 has following inputs:
   * Data Inputs A, B, C, D
   * Latch Input
   * Blanking Input
   * (Right and Left Decimal)

For 6 digits we need 36 GPIOs. Without blanking 32 GPIOs, shared latch 25 GPIOs. The Raspberry Pi has 26 GPIOs (we can have a latch for the data and a latch for the address). 

The [[http://www.sparetimegizmos.com/Hardware/Elf2K.htm][Spare Time Gizmo's Elf 2000]] display:
   * Databus
      * 8 Data Inputs
      * no strobe
   * Adressbus
      * 8 Data Inputs
      * 2 Latch Inputs
Only 18 GPIOs needed. Do not forget: the Raspberry Pi GPIOs are not 5 V compatible.

%DASHBOARD{ section="box_end" }%
%DASHBOARD{ section="dashboard_end" }%


 
-- %USERSIG{PeterSchmid - 2017-11-26}%

---++!! Comments
Attachments
Topic attachments
I	Attachment	History	Action	Size	Date	Who
jpg	LED_module.jpg	r1	manage	79.2 K	2018-05-03 - 20:14	PeterSchmid
jpg	Microdot_pHAT.jpg	r1	manage	164.3 K	2018-05-03 - 20:17	PeterSchmid
pdf	til311-e4-519224.pdf	r1	manage	90.5 K	2018-05-04 - 19:27	PeterSchmid
jpg	til311.jpg	r1	manage	96.4 K	2018-05-03 - 20:14	PeterSchmid
Topic revision: r2 - 2018-05-04 - PeterSchmid